Category: Integrated Circuit (IC)
Use: The SN65LBC176AQDR is a high-speed differential line driver and receiver designed for balanced transmission lines. It is commonly used in industrial automation, telecommunications, and automotive applications.
Characteristics: - High-speed data transmission - Differential signaling for noise immunity - Wide operating voltage range - Low power consumption - Robust design for harsh environments
Package: The SN65LBC176AQDR is available in a small outline package (SOIC) with 16 pins.
Essence: This IC serves as a reliable interface between digital systems and balanced transmission lines, ensuring accurate and efficient data transfer.
Packaging/Quantity: The SN65LBC176AQDR is typically sold in reels or tubes, with a quantity of 250 units per reel/tube.
The SN65LBC176AQDR has the following pin configuration:
1 VCC
2 AOUTB
3 AOUTA
4 GND
5 BOUTA
6 BOUTB
7 REFA
8 REFB
9 DE
10 DI
11 RO
12 VCC
13 BINA
14 BINB
15 GND
16 VCC
The SN65LBC176AQDR operates based on the principles of differential signaling. It uses two complementary signals, A and B, to represent digital information. These signals are transmitted differentially over a balanced transmission line, which helps reject common-mode noise.
The driver section converts the digital input signals (DI) into differential output signals (AOUTA and AOUTB), while the receiver section converts the received differential signals (BINA and BINB) back into digital output signals (RO).
The SN65LBC176AQDR finds application in various fields, including:
These alternative models provide similar capabilities and can be considered based on specific application requirements.
Word count: 530 words
Sure! Here are 10 common questions and answers related to the application of SN65LBC176AQDR:
Q: What is SN65LBC176AQDR? A: SN65LBC176AQDR is a differential line driver and receiver IC commonly used in industrial communication systems.
Q: What is the operating voltage range of SN65LBC176AQDR? A: The operating voltage range of SN65LBC176AQDR is typically between 4.5V and 5.5V.
Q: What is the maximum data rate supported by SN65LBC176AQDR? A: SN65LBC176AQDR supports data rates up to 20 Mbps.
Q: Can SN65LBC176AQDR be used for long-distance communication? A: Yes, SN65LBC176AQDR is designed for long-distance communication and can support cable lengths up to several hundred meters.
Q: Does SN65LBC176AQDR require external termination resistors? A: Yes, SN65LBC176AQDR requires external termination resistors to match the characteristic impedance of the transmission line.
Q: Can SN65LBC176AQDR be used in half-duplex communication systems? A: Yes, SN65LBC176AQDR can be used in both half-duplex and full-duplex communication systems.
Q: What is the power supply current consumption of SN65LBC176AQDR? A: The power supply current consumption of SN65LBC176AQDR is typically around 10 mA.
Q: Is SN65LBC176AQDR compatible with TTL logic levels? A: No, SN65LBC176AQDR operates with differential logic levels and is not directly compatible with TTL logic.
Q: Can SN65LBC176AQDR be used in harsh industrial environments? A: Yes, SN65LBC176AQDR is designed to operate reliably in harsh industrial environments with wide temperature ranges and high noise immunity.
Q: Are there any application notes or reference designs available for SN65LBC176AQDR? A: Yes, Texas Instruments provides application notes and reference designs that can help in implementing SN65LBC176AQDR in various technical solutions.
Please note that the answers provided here are general and may vary depending on specific application requirements. It is always recommended to refer to the datasheet and application notes provided by the manufacturer for detailed information.